ASTM Standards. ASTM F ASTM F – Standard Test Method for Burst Testing of Flexible Package Seals Using Internal Air Pressurization Within. Consult Labthink Instruments Co., Ltd.’s High Pressure Leak Tester for Package ASTM F, ASTM F brochure on DirectIndustry. Page: 1/4. More help in interpreting the results can be found in ASTM F Inflation Seal Strength Testing (ASTM F and F), including burst, creep and creep-to-.

Author: Vudoll Yozshull
Country: Dominica
Language: English (Spanish)
Genre: History
Published (Last): 28 October 2014
Pages: 409
PDF File Size: 12.65 Mb
ePub File Size: 3.85 Mb
ISBN: 655-4-75508-739-9
Downloads: 49109
Price: Free* [*Free Regsitration Required]
Uploader: Shasho

Oxygen Permeability Tester to test containers.

Product List | RDM Test Equipment | Assured Quality Testing Solutions

In particular it is intended as applicable to packages with seals that have a peelable seal feature peeled open by end user to remove contents of package. See Appendix X2 for further information.

Labthink provides COF Tester for coef. Link to Active This link will always route to the current Active version of the standard. F20544 caution is advised where users of this procedure may be required to design and fabricate restraining plate fixtures.

ASTM F | Rycobel

In particular it is intended as applicable to packages with seals that have a peelable seal feature peeled open by end user to remove contents of package. FT-F1 Aztm tester to to test for fogging on upholstery material and time frame for testing. Reference Appendix X3 for further information regarding calculation of stress factors and structural design considerations.

Flexible packages, aseptic packages, various plastic pilfer-proof closures, flexible tubes, caps and other materials. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as c2054 of the standard.

Link to Active This link will always route to the current Active version of the standard.

Under Test Methods F the stresses are not distributed f254 to all areas of the package seal. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. This test method also cannot provide an evaluation of overall package integrity or the burst strength of areas of the package that contact the surface of the restraining plates used.

  JAYA PARVATI VRAT KATHA IN GUJARATI PDF

Under Test Methods F the stresses are not distributed uniformly to all areas of the package aastm. This test method should be combined with other methods of evaluating overall package integrity, uniformity of the package seal, or opening functionality, if so required. See Appendix X4 for information. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

The Online Industrial Exhibition. Historical Version s – view previous versions of f2045. Reference Appendix X3 for further information regarding calculation of stress factors and structural design considerations.

MFY leak detector for our pouch packaging. Test Methods F describes methods of burst testing that do not include the use of restraining plates and are suitable to determine a packages general ability to withstand pressurization stresses.

By placing the package within restraining plates during pressurization, the dimensional stability of the package is maintained in a manner that results in stresses applied more uniformly along the perimeter of the package, where seals are normally placed. COF Inclined Plane Tester Measure the static coefficient of friction of various materials using a variable inclined plane and a sliding block.

ASTM F2054

Typical parameters can include, but are not limited to the package size, material, type and configuration of seal, rate of air flow into the package, pressure detection sensing mechanism and sensitivity machine response to pressure dropposition of test article, rigidity of restraining plates, and distance between restraining plates.

Particular caution is advised where users of this procedure may be required to design and fabricate restraining plate fixtures. This allows the test to have a higher probability of detecting the weakest area of the seal and provide a measurement of the pressure required to “burst” open the package. Seal Strength system to test 3 sides seal bags.

ASTM F2054/F2054M – 13

This test method cannot provide a measure of package seal uniformity. Tensile Tester for both compression and tensile, with loads typically N. This standard does not purport to address all of the safety concerns, if any, associated with its use. See Appendix X4 for information. Under unrestrained conditions the stress on the package is highest at the middle of the pouch where it inflates to the packages maximum diameter; therefore, Test Methods F may not reliably detect the weakest area of the seal.

  EDWARD MORAWSKI POLONEZ PDF

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Test Methods F describes methods of burst testing that do not include the use of restraining plates and are suitable to determine a packages general ability to withstand pressurization stresses.

Labthink RT rub tester to test on flexo printing. Vacuum Leak Tester for bottles for food, chemical and pharmaceutical applications. Pressure differentials may occur during such processes as sterilization and transportation. Thickness micron testing equipment with Resolution 0.

Specifications Test Range Contact: Under unrestrained conditions the stress on the package is highest at the middle of the pouch where it inflates to the packages maximum diameter; therefore, Test Methods F may not reliably detect the weakest area of the seal. This test method provides an indicator of the burst strength of a package, where the burst will normally occur in one or more areas of the seal. An indicator of awtm minimum burst strength may be of importance to the package manufacturer and end user in ensuring adequate package integrity.

Three Tests in one instrument High Pressure Leak tester With various accessories for tests of different packages Applications: MFY Leak Tester is used to look for pin holes in bags that hold calibration solutions for medical instruments. Active view current version of standard. By placing the package within restraining plates during pressurization, the dimensional stability of the package is maintained in a manner that results in stresses applied more uniformly along the perimeter of the package, where wstm are normally placed.