The DriveRack® has been designed to provide “Everything you need between the mixer and the power amps”. From the powerful DSP modules to the . View and Download Dbx DriveRack user manual online. Complete Equalization & Loudspeaker Management System. DriveRack Stereo Equalizer pdf. DriveRack™ User Manual ii. DriveRack™. Congratulations on your purchase of the dbx® DriveRack™ Complete Equalization and. Loudspeaker.
|Published (Last):||8 January 2009|
|PDF File Size:||11.21 Mb|
|ePub File Size:||10.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
Input 2 Level -Inf to 20dB Adjusts the input level of input 2.
To espol the manual completely, please, download it. Essentially this means that the first filter set is replaced where a new feedback is detected and notched out. The following information provides, descriptions about program functions and in depth configuration options of the Drivegack A straight through RS cable will not work with the DriveRack.
Making sure that all outputs are muted, apply power to the mixer and amplifiers. In the Quick Start section of this manual, you saw how you can use the Wizards to configure basic programs i.
By pressing ‘print’ button you will print only current page. Got it, continue to print.
dbx DriveRack 260 User Manual – Download
RJ connectors, the Zone Controllers offer an easy to program and use remote control surface. Master level -Inf to 20dB This parameter is used to control the overall level of the mixed input signals. This feature gives you the ability to control various parameters of the such as Output Levels, Mute and Program Changes.
This lets you choose the exact knee that is needed for the dynamic effect you are looking for. ZC-1 The ZC-1 is a programmable zone controller that allows output volume level control from a wall panel.
Additionally, pressing and holding the Utility button will allow you to enter the metering section of the The Utility Menus will appear as follows: From program mode, press the EQ button to reach the EQ module to be edited. To wire in series each Zone Controller must have an identification or zone number chosen using the DIP switches on the side of the controller see diagram A.
Bell – All bands are bell-shaped. Connections When setting up the DriveRackmake connections as follows: Successive presses of the Data wheel will select effect parameters within the currently selected page.
Successive presses of the EQ button will move through each channel. Defining The Driverack DriveRack The Soft Reset resets all operating parameters except user programs. Successive presses of the Other button will move you to each of the various insert modules available.
Pressing the Data Wheel will select the effect parameter to be edited. To instantly access an effect module, simply press the corresponding button in the button array for the desired module. Warranty In no ddiverack shall dbx or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control.
Zc-zone Controllers RJ connectors, the Zone Controllers offer an easy to program and use remote control surface. Dbx 12 series graphic equalizers operation manual 45 pages. The Auto-EQ can be used to adjust your system to compensate for room effects, and adjust the response of the entire system to your liking.
This is done by selecting a desired Target output level and Window. Pressing the DATA wheel again and rotating it then allows you to assign this binary switch combination to a program to be loaded. Up to six ZC panels can be connected to a DriveRack The upper left-hand corner of the display indicates what Crossover type is currently selected.
Pdf Download | dbx DriveRack User Manual (84 pages)
The Hard Reset Procedure will reset all programmable information back to the factory defaults. Table of Contents Add to my manuals Add. Gain structure refers to aligning the gain of each device so that they all clip at the same mnaual, and the noise floor of the entire system is at its absolute minimum. Zc Setup Output 5. After expiration of the warranty, a reasonable charge will be made for parts, labor, and packing if you choose to use the factory service facility.
Dbx DriveRack 260 User Manual
In no event shall dbx or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control. FX buttons – This array of 12 FX buttons is your primary mode of directly accessing any effect module. Don’t have an account?
Service Contact Info After expiration of the warranty, a reasonable charge will be made for parts, labor, and packing if you choose to use the factory service facility.
The upper left-hand corner of the display Program 1 indicates what EQ type is currently selected.
DBX DRIVERACK USER MANUAL Pdf Download.
FIXED mode is used before the performance without any input signal. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions driverzck you are qualified to do so.
Enter text from picture: Up to six Notch filters are available for all six outputs. Level 9 to 12 dB Sets the overall gain of the high shelf parametric 4. The A and B indicators indicate which input is currently selected. Page 3usA date: There is mamual separate collection system for used electronic products in accordance with legislation that harman music Group requires proper treatment, recovery and recycling.
Your local dbx sales and service office or If you want to dispose this product, do not mix it with general household waste.